Make a cleaning solution Make a mixture of baking soda and liquid soap using two parts baking soda with one part soap, with a bit of water. Vinegar is a non-toxic cleaner that kills mould and cleans bathroom tiles. Simply mix an equal amount of vinegar with water, and you have a non-toxic, effective cleaning solution.
If your bathroom is dirty and has stains that are difficult to remove entirely, you can use a mix of baking soda with ammonia solutions and vinegar. These three components can be beneficial in eliminating the accumulated grime and the toughest of dirt.
Bicarbonate of soda or cleaning with baking soda is an effective tile cleaner, especially for stubborn stains and grouting.
1/2 cup vinegar. 3/4 cup baking soda. 1/4 cup lemon juice. 1/4 cup dishwashing liquid.
Pour this mixture into a spray bottle and generously spray the affected area. Leave the solution to work for five minutes while you grab a cup of coffee... Use a scrubbing brush and toothbrush to scrub the area.
Baking soda is a safe deodorizer, whitener, and household cleaner—and it's an effective natural grout cleaner. Because baking soda is also a mild abrasive, using it for cleaning grout lines gives you extra firepower without the risk of scratching your tile.
Baking Soda And Vinegar
Although mixing vinegar and baking soda is not considered dangerous, you should still avoid mixing these in a container. Vinegar is acidic and basic soda is basic, so the by-products are sodium acetate, carbon dioxide, and water that are not toxic.
You should use a ratio of 1:2 baking soda to vinegar. In other words, if you're using ½ cup of baking soda, use 1 cup of vinegar, or if you're using a cup of baking soda, use 2 cups of vinegar.
Add about 1 cup of baking soda to the toilet bowl, then add another 1 to 2 cups of vinegar. You should see and hear some fizzing action—this means that it's working! Let the solution sit and fizz for about ten minutes.
The bottom line: using baking soda and vinegar to clean floor grout is great if you don't mind manual labor, you're on a budget, and you have the time to break up the process into steps. It's also a great way to spot clean or to clean in between visits from the professionals.
The time that white vinegar should sit on the tile before cleaning depends on the severity of the stains or buildup you are trying to remove. In general, it is recommended to let the white vinegar solution sit for at least five to ten minutes to penetrate and dissolve any dirt, grime, or soap scum on the tile surface.
Mixing baking soda and vinegar together can result in a volatile combination, particularly for porous stone surfaces. In some cases, this can result in discolouration or stains.
Grout that hasn't been sealed, needs to be resealed, or is in poor shape should not be cleaned with vinegar. The vinegar penetrates into the pores of the grout, further weakening the material. Over time, vinegar will deteriorate the condition of the grout by etching or wearing it away.
(If it's too thin, add more baking soda. If it's too thick, add more vinegar.) Spread the paste in a generous layer along the area of grout you're cleaning. Let it sit for 5-10 minutes.
Let the product sit for 30 minutes. Then, go back in and scrub gently with water. (Our Test Kitchen loves the Scrub Mommy scrubber for all kinds of cleanup tasks.) You'll watch the dirt melt right off the tile and grout.
What's the best homemade grout and tile cleaner? Mix together 1/2 cup of baking soda, 1/4 cup of hydrogen peroxide, and 1 tsp dish soap. Apply cleaning mixture onto the grout, wait 5-10 minutes, scrub, sweep up the excess baking soda, and rinse.
Pour baking soda into the drain (about half a cup), followed by one cup of white vinegar. Cover the drain and let it sit for 30 minutes. After waiting, boil a kettle of water and dump all of the boiling water down the drain to flush out the loosened clog.
Depending on how severe the dirt and grime build up on your tiles is, you can either dust the tiles over with a coating of baking soda and then scrub this away with a non-abrasive brush or sponge for a quick and easy finish.
To start, prepare a mixture of water and vinegar in a bucket or other large container. You can choose the ratio based on your preferences, but it's generally recommended to start with a 2:1 ratio of water to vinegar. Next, dip a soft cloth into the mixture and begin scrubbing your tiles in small, circular motions.